购物车图片 Cart ( )
Doucument Case
Hot News / Hot recommended
2017 - 07 - 03
点击次数: 76833
There are 7 parts of the document for the settings. 1. Delta Model Parameters Settings Part.2. XYZ/CoreXY Model Parameters Settings Part. 3. Motors Parameter Settings Part. 4. Temperatu...
2017 - 07 - 03
点击次数: 84942
1.Wiring diagram of Lerdge-X board and pressure film probe:Leveling points:                           = 3, use three-point detecti...
2017 - 07 - 03
点击次数: 58253
Lerdge-X Motherboard Basic Wiring Instructions1. Power supply wiringsThere is a dedicated power cable supporting with the motherboard. The power cable is separated into one red line and one black line...
2017 - 06 - 29
点击次数: 2965
Lerdge Board Auto-leveling Instructions Lerdge board supports three kinds of leveling modes:1. Manual leveling the printing platform through 4 points. This mode is simple and intuitive operation....

—— Free hotline ——

135-4332-1692

Skype:lerdge .com 

Other

Xixiang street, baoan district, shenzhen city, guangdong province

support@lerdge.com

Release Time: 2017 - 07 - 03
Browse Times:76833
说明: There are 7 parts of the document for the settings. 1. Delta Model Parameters Settings Part.2. XYZ/CoreXY Model Parameters Settings Part. 3. Motors Parameter Settings Part. 4. Temperature Parameter Settings Part. 5. Motherboard Operation Part. 6. Print Settings Part. 7. System Update Part. Acceleration:X/Y/Z/E axis maximum acceleration: set the maximum speed of each axis when moving. The greater the acceleration, the faster the changes in the speed of each axis. (Please note that excessive acceleration may cause the machine to the vibration intensifies and even lead to motor locked-rotor when it's running.)Printing Acceleration: the integrated acceleration when the printer is printing items. This value directly affects the reaction sensitivity of changing...
Release Time: 2017 - 07 - 03
Browse Times:84942
说明: 1.Wiring diagram of Lerdge-X board and pressure film probe:Leveling points:                           = 3, use three-point detection, and linear leveling.                            3, use multi-point non-linear leveling.X-axis probe offset: the starting point and nozzle are overlap in the X direction, just set to 0.Y-axis probe offset: the starting point and nozzle are overlap in the Y direction, just set to 0.Z-axis probe offset: the starting point and nozzle are overlap in the Z direction, just set to 0.Probe for Z-axis min limit: pressure film is not recommended  to be used to level and limit at the same time. Otherwise, the module needs to be...
Release Time: 2017 - 07 - 03
Browse Times:58253
说明: Lerdge-X Motherboard Basic Wiring Instructions1. Power supply wiringsThere is a dedicated power cable supporting with the motherboard. The power cable is separated into one red line and one black line. The red line is connected with DC 12V/24V power positive, and the black one is connected with the negative.The power interface on the board side is with buckle to prevent incorrect insert, but still need to pay attention to that. The correct power wiring as shown below.2. Motherboard motor drive module socket introductionLerdge-X motherboard motor drive port adopts the same interface definition with pololu module. The motherboard driver interface definition as shown belowPortDescriptionNoteENABLEMotor enable control port, the system uses low-level enable program.When the motor needs to be en...
Release Time: 2017 - 06 - 29
Browse Times:2965
说明: Lerdge Board Auto-leveling Instructions Lerdge board supports three kinds of leveling modes:1. Manual leveling the printing platform through 4 points. This mode is simple and intuitive operation. It's suitable for the printing platform with small area and good flatness.2. Three-points linear leveling mode. It's suitable for the printing platform with large area and good flatness.3. Multi-points (up to 1024 sampling points) matrix grid non-linear leveling method. It can level the printing platform with large area but bad flatness.Brief introduction of Lerdge board auto-leveling principles.Leveling principles of the Three-points linear leveling mode: The non-collinear three points determines a plane. By sampling the three non-line points on the printing platform, to calculate the plane ...
Release Time: 2013 - 11 - 30
Browse Times:3665
说明: The basic wiring diagram of the Lerdge motherboard
Release Time: 2017 - 07 - 03
Browse Times:3920
说明: Online Configuration Tool: Detailed explanation of Lerdge configuration fileUsers can use Lerdge online configuration tool for the parameters configuration. The parameters can not be saved before upgrading the firmware, so you need to download the configuration file and save the configurations. After updating the firmware, please use the U disk or TF card to update the saved parameter configuration. Entry the main interface, and then Settings → System Settings → Update.; How to use: modify the machine parameters in this text and save, and then copy it to the TF card or U disk.; Enter the "Settings" - "System" - "System Update", and select the TF card or U disk that with the configuration file.; Select and implement the configuration file. M867 S1;Set...
10页次1/2首页Previous12Next尾页
Link
Copyright ©2017 - 2017 深圳前海乐积科技有限公司
犀牛云提供企业云服务
X
3

SKYPE 设置

4

阿里旺旺设置

等待加载动态数据...

等待加载动态数据...

5

电话号码管理

  • 13543321692
6

二维码管理

等待加载动态数据...

等待加载动态数据...

展开